We use cookies to give you the best experience possible, please look at our cookies policy for more details.

Necessary Cookies - These cookies are used to allow function of this website on your device.

Analytics Cookies - These cookies are used to monitor flow of traffic and how the website is used. To improve the site for everyone.

Save and Close

How to pair the standard M-04 remote to the Level 4 control board.

*WARNING: ANY WORK CARRIED OUT INVOLVING ELECTRICITY SHOULD BE DISCUSSED WITH AN ELECTRICIAN*

Amount of Steps: 6

Requirements

Remotes to be paired
Control box with Level 4 or higher control board
Cross-Head/Phillips/Pozi Drive Screwdriver

Step 1

Cover Removal

Take off front cover of control box

Unscrew 3 x M3 self tapping screws
Gently pull the front cover off towards you

Step 2

Programming: Functions

For Normal Operational Control

Select the correct function

Ensure the screen is showing two dashes (- -)
Quick press the top button until R1 is found.

For Pedestrian Button Programming

Select the correct function

Ensure the screen is showing two dashes (- -)
Quick press the top button until R3 is found.

Step 3

Programming: Pairing

Pair the Remote

Once you have found your required function wait for it to swap to show three horizontal dashes
On the new remote hold the button down you wish to pair
Wait for the screen to show a red dot as well as the three dashes
Whilst still holding the remote button press the third button down on the control board (Labelled C).
When a number appears release Everything

Step 4

Check Pairing

Test if the pairing was successful

Make sure R1 or R3 is still selected on the board with the three dashes shown.
Press the button on the remote you just paired.
If a number appears the pairing was successful

Step 5

Exit Functions

Return the board to Standby

Quick Press the top button on the control board until two dashes
appear (- -).

Step 6

Cover Replacement

Replace cover

Gently replace box front cover avoiding trapping any wires or allowing any gaps in the seal.
Refit 3 x M3 self tapping screws

EON400FX

For Super Fast Gate Automation

From £500

Buy

Super Fast, Strong, Sleek

For times when fast gate automation is crucial.

Product Details

Product Name:EON400FX

Weight (Per Arm): 6Kg

Capacitor Required:8 µF

Max Leaf Length: 4 Meters

Opening Time:10 Seconds

Power Use (Per Arm):350W

Duty Cycle:40%

Max Force:2200N

Power:230V AC 50 / 60Hz

Current Draw (1 Motor):0.9 - 1.5 Amps

Rating:IP44

Max Leaf Weight:300kg

Buy

Available with a range of accessories and as dual or single kits.

The EON400FX is born from our most reliable gate automation with the added bonus of a superfast motor, reducing the opening time to 10 seconds!

As with all of our rams we pride ourselves on the engineering, all of our rams contain metal gearing and drive shafts to create a robust system.

We strongly believe in the right to repair, as such in the rare case you will need them we have replacement parts available for all of our systems including the EON400FX.

All of our systems are hand made in North Italy, just south of Vicenza. So benefit from a strong Italian Manufacturing history.

The NEO400 has the electric motor positioned above the shaft, this lends itself nicely to being mounted lower to the ground when required due to the gate structure.

As with all of our rams we pride ourselves on the engineering, all of our gate automation contain metal gearing and drive shafts to create a robust system.

We strongly believe in the right to repair, as such in the rare case you will need them we have replacement parts available for all of our systems including the NEO400.

All of our systems are hand made in North Italy, just south of Vicenza. So benefit from a strong Italian Manufacturing history.

Dimensions

Please use these dimensions as a rough guide for your reference.

The dimensions below show the usable ram length, any installation that extends or retracts the stroke length further than this will void the warranty.

Common FAQ's

Yes, this ram must have physical stops for the gate to hit against in both the open and closed positions. This not only protects the rams from running to the end of its travel, it also allows smooth and consistent performance.

Yes, our systems allow for third party GSM, WIFI and Bluetooth controllers to be connected to it. This is achieved by connecting a 'Normally Open' relay in the third party module, providing a 1 second pulse to terminals 1 and 8 on our control board, for normal operation.

Depending on the length of the gate these openers at the longest gate length of 4 meters can move a gate of 300kg. Something to be considered is the strength of wind, if there is extremely strong wind then caution should be used when deciding whether to use the openers or not, especially if the gates are fully boarded (A.K.A Sail Gates).

The system can handle up to 99 remotes as standard. This can be increased with additional modules. For large amounts of access systems required we suggest looking into our keypad, or another third party entry module i.e. Intercom

The standard opening angles available are 90 degrees and 100 degrees. This is set by trigonometry to enable the movement of the gate correctly. The correct measurements for this can be found in the fitting guide.

Yes, that is one of the two ways these motors can be mounted, if you take a look at our swing gate fitting guide it explains with a diagram the difference between mounting positions for the ram.

The NEO has a manual release lock situated on the front of the device. This can be released with the supplied key.

The average range of the remotes is dependent on the environment, 50 meters is common.